Featured Member
ID:
scotswind
Since: 1/3/2008
From: Newark on Trent United Kingdom
Rating:
(0.0)
Featured Picture
Google Ads
|
1 | 2 | Page 3 | 4
Ed Strege of Badger State Repair, the master of brasswind repair, continues his series of brass ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Ed Strege of Badger State Repair, gives a quick tip on fitting flute head joints with just the ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Ed Strege of Badger State Repair, offers a few tips on repairing a sluggish second piston and ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Ed Strege of Badger State Repair, the master of brasswind repair, goes over the basics of ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Bob Baier discusses a jig he uses in replacing lower joint sockets on the Vito bass clarinet. This ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Bob Baier demonstrates how to restring and adjust rotary valves. To view the video you must have ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Larry Mueller, professional oboists and repair technician, takes you step by step through the ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Larry Mueller gives an overview of the drill press, including maintenance and setup, and shows ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Ed Strege of Badger State Repair, the master of brasswind repair, demonstrates how to straighten ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Ever have a piece of the hinge rod that forms part of the screw driver slot break off? Ed Strege ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Ed Strege of Badger State Repair shows the final step in repairing damaged flute tone holes - ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Ed Strege of Badger State Repair shows how to properly and safely bend a replacement French horn ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Michael Durocher, instructor of the Keyano College Musical Instrument Repair program in Alberto ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
David continues his Silencing Rotor Valves clinic with removing the end play from the rotor ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
David continues his Silencing Rotor Valves clinic with the process of removing the side play from ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
After a short introduction, David Laws goes over preliminary information needed to demonstrate how ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
This video is an absolute must for all professional repair technicians that would like to provide ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
David Laws demonstrates a method for oiling rotor valves that gets the oil where it needs to be - ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Ben Schildgen of West Music offers a few time saving tips on case repair, soldering, and chem ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
Peter Hart takes us around his shop at West Music and discusses the various dent tools and their ...
|
- Rating: [0.0] By: (0) users
- Views: 0
|
1 | 2 | Page 3 | 4
|
Login
Shout Box
- (10/9 17:13) ChrisHarnett: Doesn't seem very promising
- (10/6 12:46) DriverDrobina: Is this site still active?
- (10/6 12:45) DriverDrobina: I have the same concern
- (6/2 17:51) Wailinfree: is this site still active?
- (6/2 17:51) Wailinfree: is this site still active?
- (4/29 12:46) BENSCHILDGEN: Cleaning snakes nowdays SUCK!
- (12/4 22:44) dparker: Hey Brent!
- (11/26 20:46) crousfrench: I'm back. Did you miss me?
- (10/9 7:18) BENSCHILDGEN: What's going on out there?
- (6/1 18:53) dparker: dparker@ciomit.com www.ciomit.com
- (6/1 18:53) dparker: or we can do an online meeting
- (6/1 18:53) dparker: It can be dangerous. If you could send some pic
- (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
- (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
- (5/25 5:9) BENSCHILDGEN: I had an old tuba that I could not get it apart.
- (5/25 5:8) BENSCHILDGEN: I just do not know much about the whole mechainsm
- (5/24 14:2) dparker: How can I help with the clock springs?
- (5/24 14:2) dparker: How can I help with the clock springs?
- (5/18 5:9) BENSCHILDGEN: MAYBE THIS SITE SHOULD BE LINKED TO FACEBOOK
- (4/26 7:20) BENSCHILDGEN: I need info on tubas with clocksprings for levers
- (4/4 8:34) dparker: Indeed! I will be posting more soon!ore soon!
- (3/30 11:36) BENSCHILDGEN: Let's try to get this site flowing again
- (7/6 19:46) Krch: My favorite is uses for electric soldering guns!
- (6/13 9:0) crousfrench: I still enjoy watching the videos over and over
- (6/13 8:59) crousfrench: I haven't seen anything new in awhile, but
- (5/31 21:36) Krch: articles...articles
|