Professional Band Instrument Repair Technician Logo

Featured Member

ID: t-tane
Since: 8/28/2007
From: Helsinki Finland
Rating: (0.0)

Featured Picture

Google Ads

  Active TopicsActive Topics  Display List of Forum MembersMemberlist  Search The ForumSearch  HelpHelp
Trombones
 PROBIRT Forums » Trombones
Subject Topic: Straightening Questionable Slide Tubes Post ReplyPost New Topic
Author
Message << Prev Topic | Next Topic >>
NealAnderson
Technician & Clinician
Technician & Clinician


Joined: March.15.05
Location: USA
Online Status: Offline
Posts: 0
Posted: March.23.05 at 8:58am | IP Logged Quote NealAnderson

Have you ever had a trombone in your shop that had tubes that you were afraid would buckle due to red rot if you tried to straighten them? ...or tubes that were too severely bent for just drawing the dent out?
Try this:
Take a slide mandrel and put it at the EXACT location of the bend. Chuck it in a vise and use it to "rebound" the slide back straight. This is VERY immediate and VERY direct. You only need medium-strength blows at the hardest and check frequently.
One blow may be enough!
After straightening using this method, there is sometimes (though not that often) a bit of distortion where the end of the mandrel contacted the opposite side of the slide. Tap this area down and use a slide expander to lightly burnish this area back round.
Voila! With some practice, you'll add this technique to your arsenal and repair slide tubes you previously thought couldn't be repaired!

Happy straightening!
Back to Top View NealAnderson's Profile Search for other posts by NealAnderson
 
MattStevens
Technician
Technician
Avatar

Joined: January.19.05
Location: USA
Online Status: Offline
Posts: 3
Posted: March.25.05 at 4:30pm | IP Logged Quote MattStevens

When trying to straighten slide tubes that you don't want to do the regular way (pushing down with a rag or something while rubbing the length of the tube), try this: After using the Ferree's N87A (one of the best and easiest to use tools I have ever seen) over the last few years, I've found that it has a tendency to slightly bend the tubes (which I can usually straighten in one shot by the traditional method). The nice thing is that it's always predictable - if I'm using the pliers on the top side it bends slightly down....if I'm on the right side, it bends left, etc. I now use this method to STRAIGHTEN tubes with the support of a tight mandrel running the length of the tube, with no possible chance of a collapse.
Back to Top View MattStevens's Profile Search for other posts by MattStevens Visit MattStevens's Homepage
 
michaeldurocher
Technician
Technician
Avatar

Joined: September.25.05
Location: Canada
Online Status: Offline
Posts: 0
Posted: October.02.05 at 9:23pm | IP Logged Quote michaeldurocher

Message one worries me about possibly bending a hand slide mandrel.

When I was first taught I was shown how to burnish on the mandrels but found that non of the mandrels we straight and caused more problems for me later.

I ended up buying a new set of mandrels that give me a true product everytime faster.

Mike
Back to Top View michaeldurocher's Profile Search for other posts by michaeldurocher
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic
Printable version Printable version

Forum Jump
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Powered by Web Wiz Forums version 7.9
Copyright ©2001-2004 Web Wiz Guide

This page was generated in 0.1016 seconds.

Login

Login to view contents and post messages and reviews
Username:
Password:

New Member Registration
Retrieve Lost Password

Shout Box

  • (10/9 17:13) ChrisHarnett: Doesn't seem very promising
  • (10/6 12:46) DriverDrobina: Is this site still active?
  • (10/6 12:45) DriverDrobina: I have the same concern
  • (6/2 17:51) Wailinfree: is this site still active?
  • (6/2 17:51) Wailinfree: is this site still active?
  • (4/29 12:46) BENSCHILDGEN: Cleaning snakes nowdays SUCK!
  • (12/4 22:44) dparker: Hey Brent!
  • (11/26 20:46) crousfrench: I'm back. Did you miss me?
  • (10/9 7:18) BENSCHILDGEN: What's going on out there?
  • (6/1 18:53) dparker: dparker@ciomit.com www.ciomit.com
  • (6/1 18:53) dparker: or we can do an online meeting
  • (6/1 18:53) dparker: It can be dangerous. If you could send some pic
  • (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
  • (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
  • (5/25 5:9) BENSCHILDGEN: I had an old tuba that I could not get it apart.
  • (5/25 5:8) BENSCHILDGEN: I just do not know much about the whole mechainsm
  • (5/24 14:2) dparker: How can I help with the clock springs?
  • (5/24 14:2) dparker: How can I help with the clock springs?
  • (5/18 5:9) BENSCHILDGEN: MAYBE THIS SITE SHOULD BE LINKED TO FACEBOOK
  • (4/26 7:20) BENSCHILDGEN: I need info on tubas with clocksprings for levers
  • (4/4 8:34) dparker: Indeed! I will be posting more soon!ore soon!
  • (3/30 11:36) BENSCHILDGEN: Let's try to get this site flowing again
  • (7/6 19:46) Krch: My favorite is uses for electric soldering guns!
  • (6/13 9:0) crousfrench: I still enjoy watching the videos over and over
  • (6/13 8:59) crousfrench: I haven't seen anything new in awhile, but
  • (5/31 21:36) Krch: articles...articles
SmartFlix.com How-To DVD Rental