Professional Band Instrument Repair Technician Logo

Featured Member

ID: MusicMedic
Since: 1/24/2005
From:  USA
Rating: (0.0)

Featured Picture

Google Ads

  Active TopicsActive Topics  Display List of Forum MembersMemberlist  Search The ForumSearch  HelpHelp
Other Repair Topics
 PROBIRT Forums » Other Repair Topics
Subject Topic: Buffing dust collection Post ReplyPost New Topic
Author
Message << Prev Topic | Next Topic >>
KenHulse
Technician
Technician


Joined: January.17.05
Location: USA
Online Status: Offline
Posts: 0
Posted: December.03.05 at 7:26am | IP Logged Quote KenHulse

Hello All!
I've been thinking about ways to improve the air quality in my shop. We have a seperate room for buffing, but no means of removing the dust from the environment. I was thinking about getting a cyclone dust collector with a couple of filter bags that can filter as small as 1/2 a micron. Would this be the best choice or does anyone have any other suggestions?
Back to Top View KenHulse's Profile Search for other posts by KenHulse
 
bobbaier
Technician
Technician


Joined: February.07.05
Location: USA
Online Status: Offline
Posts: 30
Posted: December.06.05 at 5:56pm | IP Logged Quote bobbaier

Since no experts have jumped in here, I'll venture a commment based on setups I have seen. I'm not sure of the micron size, but the dust from Burns red rouge on a flannel wheel seems to be smaller than anything.

One consideration for dust collection is the noise of the equipment. If you're in an overhaul shop and doing a lot of buffing, having the dust collection in another room cuts down the noise level and stress. You want a lot of air moving through the hoods--enough to take a clarinet key if you drop it. Run the duct for the collector along the floor and up the wall to the collection unit with a clean out port at the floor level to retrieve small parts.

One shop had the collector and filter bag inside a small room that had walls of 1/8" pegboard on both sides and unfaced fiberglass insulation between the walls to filter out small particles that the bags didn't get. I imagine you could find some good filters that could be easily changed in place of the unfaced fiberglass. Caulking and weatherstripping are a must to keep the dust contained.

bob
Back to Top View bobbaier's Profile Search for other posts by bobbaier
 
Greg
Technician
Technician


Joined: June.27.05
Location: USA
Online Status: Offline
Posts: 6
Posted: May.10.06 at 12:25pm | IP Logged Quote Greg

Ken,

I too am investing in a new dust collection system and am going with a Grizzly Cyclone. I haven't decided on which model yet. I have gotten some very positive reviews on these cyclones, and they are quite affordable. Let me know if you have purchased a system yet to bring me current on what you've done. Thanks

Greg
Back to Top View Greg's Profile Search for other posts by Greg
 
ellenopel
Technician
Technician


Joined: January.19.05
Location: USA
Online Status: Offline
Posts: 2
Posted: May.24.06 at 10:59am | IP Logged Quote ellenopel

The Grizzly cyclones are used here in out luthier shop. There are two of them although the space is quite large. They are excellent. They are both used for the fine finish sanding and also the floor sweepings.

Hope that helps.
Back to Top View ellenopel's Profile Search for other posts by ellenopel
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic
Printable version Printable version

Forum Jump
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Powered by Web Wiz Forums version 7.9
Copyright ©2001-2004 Web Wiz Guide

This page was generated in 0.0938 seconds.

Login

Login to view contents and post messages and reviews
Username:
Password:

New Member Registration
Retrieve Lost Password

Shout Box

  • (10/9 17:13) ChrisHarnett: Doesn't seem very promising
  • (10/6 12:46) DriverDrobina: Is this site still active?
  • (10/6 12:45) DriverDrobina: I have the same concern
  • (6/2 17:51) Wailinfree: is this site still active?
  • (6/2 17:51) Wailinfree: is this site still active?
  • (4/29 12:46) BENSCHILDGEN: Cleaning snakes nowdays SUCK!
  • (12/4 22:44) dparker: Hey Brent!
  • (11/26 20:46) crousfrench: I'm back. Did you miss me?
  • (10/9 7:18) BENSCHILDGEN: What's going on out there?
  • (6/1 18:53) dparker: dparker@ciomit.com www.ciomit.com
  • (6/1 18:53) dparker: or we can do an online meeting
  • (6/1 18:53) dparker: It can be dangerous. If you could send some pic
  • (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
  • (5/25 5:17) BENSCHILDGEN: It seemed as if it was silver brazed together
  • (5/25 5:9) BENSCHILDGEN: I had an old tuba that I could not get it apart.
  • (5/25 5:8) BENSCHILDGEN: I just do not know much about the whole mechainsm
  • (5/24 14:2) dparker: How can I help with the clock springs?
  • (5/24 14:2) dparker: How can I help with the clock springs?
  • (5/18 5:9) BENSCHILDGEN: MAYBE THIS SITE SHOULD BE LINKED TO FACEBOOK
  • (4/26 7:20) BENSCHILDGEN: I need info on tubas with clocksprings for levers
  • (4/4 8:34) dparker: Indeed! I will be posting more soon!ore soon!
  • (3/30 11:36) BENSCHILDGEN: Let's try to get this site flowing again
  • (7/6 19:46) Krch: My favorite is uses for electric soldering guns!
  • (6/13 9:0) crousfrench: I still enjoy watching the videos over and over
  • (6/13 8:59) crousfrench: I haven't seen anything new in awhile, but
  • (5/31 21:36) Krch: articles...articles
SmartFlix.com How-To DVD Rental